quattroo
Podstawowy
Sierżant sztabowy · 624 pkt
Hemel Hempstead, Hertfordshire, United Kingdom
Członek od Lip 2022
Ostatnio online 2 lat temu
Wiek 58
quattroo’s dzienniki budowy
1 blogObserwujący
3 obserwującysNajnowsze przesyłki
Najnowsza aktywność
Ostatnio opublikowano 2 lat temu
Part 26 Bit of Colourso now most of the main parts are completed i decided to paint the main colours and also dirty it up a touch so colour is Seasick Green apparently well i ordered some and eeerrrr it was almost i luminous so to…
+3♥ 10 likes1,990 viewsPart 25 Bow PulpitHere is where i have made the Bow pulpit from brass wire and a small bit of brass sheet to hold the uprights in place lots of pictures viewed here to get this as best i could i then cut a piece of ply and heat…
+1♥ 10 likes1,976 viewspart 24 masti have now painted it and smoothed off in prime grey and refitted looks a lot better now ⛵
+3♥ 10 likes2,142 viewsRe: Part 23 Mastto be fair after all that brass it isn't that heavy and with previous testing its going to need a lot of lead in the hull to get it to sit correctly once finished♥ 5 likes2,146 viewsPart 23 MastHere is were i went a bit creative adding features to the mast and going off the film boat the top marker lights and the support rings and the winder mechanism i 3d printed everything else is brass wire and tu…
♥ 10 likes2,219 viewsPart 22 MastNow for the moment of truth lets fit it to the superstructure and floor as seen in the three pictures it has gone on quite well and is removable to note the wooden block base also has a 10 mm hole through it t…
♥ 10 likes2,226 viewsPart 21 Mastthe next thing was to get the mast to the correct length so just soldering it would not do because a soon as you knock it it'll break so what i did was drill holes in both ends of the joining parts rolled a bi…
+1♥ 10 likes2,230 viewsPart 20 MastSo i have ordered a load of brass tube and assorted wire and bits and bobs there is a plan for the mast on the Sarik plans but i have not followed them instead i have just gone off photos of the film boat not …
♥ 10 likes2,239 viewsPart 19well after a we bit of mental block time i have got back to the Sarik Orca not a lot has gone on with the main Hull and Super structure apart from it now being smoothed off and primed all in Grey come on i hea…
♥ 10 likes2,247 viewsHelp required if possiblehttps://m.yeggi.com/q/seabex+one/567 views
+3♥ 10 likes1,990 viewsPart 25 Bow PulpitHere is where i have made the Bow pulpit from brass wire and a small bit of brass sheet to hold the uprights in place lots of pictures viewed here to get this as best i could i then cut a piece of ply and heat…+1♥ 10 likes1,976 viewspart 24 masti have now painted it and smoothed off in prime grey and refitted looks a lot better now ⛵+3♥ 10 likes2,142 viewsRe: Part 23 Mastto be fair after all that brass it isn't that heavy and with previous testing its going to need a lot of lead in the hull to get it to sit correctly once finished♥ 5 likes2,146 viewsPart 23 MastHere is were i went a bit creative adding features to the mast and going off the film boat the top marker lights and the support rings and the winder mechanism i 3d printed everything else is brass wire and tu…♥ 10 likes2,219 viewsPart 22 MastNow for the moment of truth lets fit it to the superstructure and floor as seen in the three pictures it has gone on quite well and is removable to note the wooden block base also has a 10 mm hole through it t…♥ 10 likes2,226 viewsPart 21 Mastthe next thing was to get the mast to the correct length so just soldering it would not do because a soon as you knock it it'll break so what i did was drill holes in both ends of the joining parts rolled a bi…+1♥ 10 likes2,230 viewsPart 20 MastSo i have ordered a load of brass tube and assorted wire and bits and bobs there is a plan for the mast on the Sarik plans but i have not followed them instead i have just gone off photos of the film boat not …♥ 10 likes2,239 viewsPart 19well after a we bit of mental block time i have got back to the Sarik Orca not a lot has gone on with the main Hull and Super structure apart from it now being smoothed off and primed all in Grey come on i hea…♥ 10 likes2,247 viewsHelp required if possiblehttps://m.yeggi.com/q/seabex+one/567 views