restin
Podstawowy
Starszy marynarz · 117 pkt
Norwich, Norfolk, United Kingdom
Członek od Sty 2015
Ostatnio online 25 dni temu
restin’s port
3 łódźs(Pleasure Craft) Swordsman
A little underpowered so a work in progress (Motor: MFA RE 540/1) (ESC: Brushed Marine ESC-50) (8/10)
(Other) Dauntless
The original boat, commuted up the river hudson to New York and belonged to the Rothschild Family, it could…
(Pleasure Craft) Precedent Huntsman 31
Performance satisfaction is a work in progress. (Motor: MFA Torpedo 850) (ESC: Brushed Marine ESC-50) (5/10)
Najnowsze przesyłki
Najnowsza aktywność
Ostatnio opublikowano 11 lat temu
(Pleasure Craft) SwordsmanA little underpowered so a work in progress (Motor: MFA RE 540/1) (ESC: Brushed Marine ESC-50) (8/10)417 views(Other) DauntlessThe original boat, commuted up the river hudson to New York and belonged to the Rothschild Family, it could top 50mph if needed. (Motor: turnigy sk3 3536-1400kv) (ESC: Hobbyking) (10/10)
417 viewsCounter Rotating Props.I am soon to start building the Dumas Dauntless boat and I need to decide on the merits or drawbacks of counter rotating props. Also as It has 2 motors I will have to decide on Brushed Or Brushless and what si…1 reply1,310 viewsPrecedent Huntsman 461/2 InchHI Mark, Hope you enjoyed your break. The boat was great this Sunday, planed nicely and was very responsive to the controls. The crack is minor, where the skins meet on the keel, not deep and the joins behind …11,532 viewsPrecedent Huntsman 461/2 InchHI Mark, Does your method of covering hull with nylon and varnish work on Painted surface (IE acrylic paint)? I found a hairline crack running down the bow, although it does not leak into boat I would feel bet…11,532 viewsPrecedent Huntsman 461/2 InchHI Mark, Prop stayed on OK but will be adding thread lock as you suggested. Boat took a real hammering on the rough water but only took 1 thimble full of water in half an hour of boating hell. Hard to say if t…
11,532 viewsPrecedent Huntsman 461/2 InchHI Mark, Ready to launch this sunday if nothing goes wrong, Everything responds to the transmitter OK I just hope that the propshaft nuts are tight enough to prevent losing prop. How do I tell if prop is turni…11,532 viewsPrecedent Huntsman 461/2 InchThanks Mark, Checked pushrods and OK, info on Motor noted, thanks. Thanks Paul, Will attempt to upload pics. hope they work this time. Regards Glyn
11,532 viewsPrecedent Huntsman 461/2 InchHI Folk, Does it matter which end of the motor is used to drive the Prop shaft? I cannot get at the end bolts that hold the motor to its frame unless I turn the motor around. Regards Glyn11,458 viewsPrecedent Huntsman 461/2 InchHI hutchinson, First time I have fitted servo so I hope I've done it right. Please see pic. I know that I need to cut the spare rod that overhangs on the rudder end, but have I done right in having 2 rods on s…11,458 views
417 viewsCounter Rotating Props.I am soon to start building the Dumas Dauntless boat and I need to decide on the merits or drawbacks of counter rotating props. Also as It has 2 motors I will have to decide on Brushed Or Brushless and what si…1 reply1,310 viewsPrecedent Huntsman 461/2 InchHI Mark, Hope you enjoyed your break. The boat was great this Sunday, planed nicely and was very responsive to the controls. The crack is minor, where the skins meet on the keel, not deep and the joins behind …11,532 viewsPrecedent Huntsman 461/2 InchHI Mark, Does your method of covering hull with nylon and varnish work on Painted surface (IE acrylic paint)? I found a hairline crack running down the bow, although it does not leak into boat I would feel bet…11,532 viewsPrecedent Huntsman 461/2 InchHI Mark, Prop stayed on OK but will be adding thread lock as you suggested. Boat took a real hammering on the rough water but only took 1 thimble full of water in half an hour of boating hell. Hard to say if t…11,532 viewsPrecedent Huntsman 461/2 InchHI Mark, Ready to launch this sunday if nothing goes wrong, Everything responds to the transmitter OK I just hope that the propshaft nuts are tight enough to prevent losing prop. How do I tell if prop is turni…11,532 viewsPrecedent Huntsman 461/2 InchThanks Mark, Checked pushrods and OK, info on Motor noted, thanks. Thanks Paul, Will attempt to upload pics. hope they work this time. Regards Glyn11,532 viewsPrecedent Huntsman 461/2 InchHI Folk, Does it matter which end of the motor is used to drive the Prop shaft? I cannot get at the end bolts that hold the motor to its frame unless I turn the motor around. Regards Glyn11,458 viewsPrecedent Huntsman 461/2 InchHI hutchinson, First time I have fitted servo so I hope I've done it right. Please see pic. I know that I need to cut the spare rod that overhangs on the rudder end, but have I done right in having 2 rods on s…11,458 views